Waterproof Modifier

[2015/12/8]

 ◆             Introduction

There is no exact standard to measure this kind of product, therefore, work out this standard as a rule for producing and trading. 

Twrite this standard based on the rule of GB/T 1.1-2009.

This standard carries out in October, 2014 and it shall go into effect on the day they are issued. Its valid for three years and review at the deadline.

Shandong Square Sea International Trade Co., Ltd. puts forward and drafts it.

Main draftsmen: Wangtao, Li hongqiang.

 

 

◆     Styrene-Butadiene Rubber Granule 

1. Purview

This standard limits some rules of styrene-butadiene rubber granule, such as, technical requirements, test methods, inspection rules, mark, packing, transportation and storage.

This standard applies to styrene-butadiene rubber granule. It mainly used as raw materials of producing rubber goods, furthermore it also used to make polymer modification, asphalt modification and plastics toughening, etc. 

2. Reference

The following paper is an essential part of this file. The references which have date are applied to this standard if not have date the new version applies to it.

GB/T 191 packaging-pictorial marking for handling of goods

GB/T 1232.1 rubber, unvulcanized-determination using a shearing-disc viscometer, part one, determination of Mooney Viscosity.

GB/T 8656 evaluation method of styrene-butadiene rubber (SBR)-emulsion and solution-polymerized types- evaluation procedures

GB/T 8658 determination of solution-polymerized styrene-butadiene rubber (SBR) raw rubber bound styrene content, refractive index method

GB/T 15340 sampling point and sample preparation methods of natural raw and composite rubber 

3. Requirements 

The project index of product control should follow requirements of chart one.

Chart 1

Project

 Index

Appearance

White columnar granule

Moisture content %                                    ≤

2.5

Molecular weight

Two hundred thousandthree hundred thousand

Bound styrene quality score, %

21.535.0

Raw rubber mooney viscosity, ML1+4100

3868

300% Modulus, MPa

1015

Tensile strengthMPa                               ≥

21

Elongation at break, %                              ≥

320

4. Experimental method

4.1 Appearance

Visual observation

4.2 Determination of moisture content

4.2.1 Test procedure

Using watch glass to weigh 5g (accurate to 0.0001g) test sample, put it in oven and dry to constant weight under 105℃±2℃. Then take it out, put into desiccator and cool to room temperature. In the end, weigh up it.

4.2.2 Calculation

Calculating moisture content X1(%) according to formula (1) :

(1)

Formula (1):

m-quality of test sample before drying, g;

m1-quality of test sample after drying, g.

4.3 Determination of bound styrene quality score

Determine it according to GB/T 8658.

4.4 Determination of raw rubber mooney viscosity

Determine it according to GB/T 1232.1.

4.5 Determination of 300% modulus, tensile strength and elongation at break.

Determine it according to GB/T 8656.

5. Inspection rule

5.1 Factory inspection

Products should test by quality inspection department and be an acceptable product with certificate of quality before leave the factory. The certificate of quality including manufactory name, product name, date of manufacture or lot number, standard number, examination date, examiner and inspection result, etc. The projects of factory inspection are appearance, fineness and moisture content.

5.2 Combined lots and sampling

The same lot products divided into a batch. According to GB/T 15240 to take samples and separately put it into two lightproof aluminium foil papers for vacuum seal. Then they attach labels and give clear indication of product name, date of manufacture or lot number, sampling date and examiner, etc. One samples for test another for storage.

5.3 Determination

It can be considered as qualified products as long as all the test results follow this standard. If the result doesn’t conform to this standard requirement, it should take double samples to check again. When all the results conform to this standard, it can be recognized as accepted products or it can be considered as unaccepted goods.

5.4 Model inspection

One of the following cases should take model inspection:

A) firstly go into operation;

B) Great changes of raw materials and technology;

C) Requirements put forward by consumers and technical supervision department;

D) Taking model inspection at least once every two months in general production.

Model inspection projects are all projects that decided by this standard.

6. Mark, packing, transportation and storage

6.1 Mark

The package of products should have clear and firm mark. It includes manufactory name, product name, date of manufacture or lot number, net volume, standard number, avoid direct sunlight and rain markings of GB/T 191, etc.

6.2 Packing 

Products’ sealed package has two layers, the inner one is black polyethylene vacuum package and the outside is carton.

6.3 Transportation 

In the transportation process, avoid insolation, rain and take care of products to prevent packing damage.

6.4 Storage 

Store in shade, ventilated and dry storehouse, avoid pile up in open air and under direct sunlight.

7. Security

Styrene-butadiene rubber granule stores in vacuum package. It easily causes self-ignition if left untouched for long periods of time after open it, therefore, timely seal up it.

 

Up:
Down:

Related news

Custom Service